Stone chip protection AQUA
Gravel guard AQUA
GRVLGUA-AQUA-BLACK-1LTR
Register now and access more than 125,000 products
- Dries completely down to -10 °C
- Fine and coarse structures can be sprayed depending on the application
- Excellent anti-humming effect
- Very high abrasion resistance
- Suitable for oven drying
- Very easy to sand once completely dry
Dries down to -10 °C. When painting, ambient influences must be taken into account. Do not spray on joints, engines, gears and brake systems. Dilution with water (max. 2 %) possible. With IR (infrared) drying, the following must be taken into account: Maximum drying time depends on the temperature, coat thickness, fresh air and air supply. The material must not be heated above max. 60 °C during IR drying, as blistering may occur
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.
Datasheets(X)
For repairing and restoring the original texture and for protecting against stone chips and corrosion in all visible areas, e.g. front and rear bumpers, side members etc.
Shake can well before use. The base material must be dry and free from rust, dirt and grease. Old coating compound should be removed. Can be painted over with all paint systems after approx. two hours (depending on the coat thickness), especially water-based paints. The optimum spraying distance is 20-30 cm. Spray a very thin coat for the first coat to provide improved adhesion and let it flash off for approx. three minutes. Then apply the required coat thickness. Allow each intermediate coat to flash off. Different textures are achieved by adjusting the compressed air and nozzle supply. Clean gun thoroughly using water after every use. Aqua gravel guard can be mixed with water-based paints to a proportion of up to 30 %. Dirty surfaces can be cleaned with water before drying fully. Once the product is completely dry, it can be painted over with commercially available 2-component acrylic paints and base coats. We recommend applying a primer before using 2-component acrylic paint. Operating pressure: 3-6 bar.
Chemical basis | Aqueous synthetic dispersions, fillers and additives |
Contents | 1 l |
Weight of content | 1.05 kg |
Colour | Black |
Max. processing temperature | 25 °C |
Min./max. processing temperature /conditions | -10 to 25 °C / at 20°C and 65% relative humidity |
Conditions for through drying | at 20°C, 500 μ wet |
Max. pressure | 6 bar |
Max. temperature conditions | 35 °C |
Min./max. temperature conditions | 15 to 35 °C |
Min. pressure | 3 bar |
Min./max. spraying distance | 20-30 cm |
Can be varnished after | 12 h |
Conditions for drying time | at 20°C and 65% relative humidity |
Density/conditions | 1.05 kg/l / at 20°C, DIN 51757 |
Min./max. temperature resistance | -25 to 80 °C |
Shelf life from production/conditions | 12 Month / at 10°C to 30°C |
Conditions to maintain shelf life from production | at 10°C to 30°C |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Cable knife
Plus hand cleaner
Vacuum lifter with one head
Intensive wheel rim cleaner For all painted and unpainted light metal wheel rims and steel rims
Halogen bulb
Slide hammer for dent lifter adhesive adapters and pin puller rivets
Starlock saw set
3/4-inch impact socket wrench insert hexagon, metric, long
Cooling system tester
Metric combination wrench with POWERDRIV®