All-rounder injectable mortar WIT-VM 250 - ANC-MORT-(WIT-VM250)-420ML

All-rounder injectable mortar WIT-VM 250 - ANC-MORT-(WIT-VM250)-420ML - 1

All-rounder injectable mortar WIT-VM 250 - ANC-MORT-(WIT-VM250)-420ML - 2

All-rounder injectable mortar WIT-VM 250 - ANC-MORT-(WIT-VM250)-420ML - 3

All-rounder injectable mortar WIT-VM 250 - ANC-MORT-(WIT-VM250)-420ML - 4

All-rounder injectable mortar WIT-VM 250

Name: All-rounder injectable mortar WIT-VM 250
Brand: Würth
SKU: 0903450205

All-rounder chemical injection mortar WIT-VM 250
ANC-MORT-(WIT-VM250)-420ML

Art.-no. 0903450205

EAN 4046777045314

All versions

Prices for customers after login

All-rounder injectable mortar WIT-VM 250

Art.-no. 0903450205

Prices for customers after login

Quantity

x 12 pcs

Exclusively for trade customers

Locate shop
Login/Register
Call customer service: +254724257046

The all-rounder for concrete, masonry and post-installed rebar connections

Two-component resin mortar, styrene-free vinyl ester

Individual fixing point, cracked and uncracked concrete, seismic performance category C1

W-VI-A anchor rod, W-VD-A anchor rod, standard threaded rod with acceptance test certificate 3.1

Individual fixing point for masonry (system with WIT-SH perforated sleeve):

WIT-SH perforated sleeve, WIT-AS anchor rod, WIT-IG internally threaded sleeve

Individual fixing point for masonry (system with SH perforated sleeve):

SH perforated sleeve, W-VI-A anchor rod, W-VI-IG internal thread anchor, standard threaded rod with acceptance test certificate 3.1

Post-installed rebar connection

Proof of Performance

European Technical Assessment ETA-12/0164: Individual fixing point + cracked and uncracked concrete (W-VD-A anchor rod, standard threaded rod with acceptance test certificate 3.1), seismic performance category C1

European Technical Assessment ETA-13/1040: Individual fixing point + masonry consisting of solid and perforated block, autoclaved aerated concrete (WIT-SH perforated sleeve, WIT-AS anchor rod, WIT-IG internally threaded sleeve, autoclaved aerated concrete only with WIT-SH 18x95 perforated sleeve)

European Technical Assessment ETA-16/0757 and ETA-20/0854: Individual fixing point + masonry consisting of solid and perforated block, autoclaved aerated concrete (SH perforated sleeve, W-VI-A anchor rod, W-VI-IG internal thread anchor, threaded rod with acceptance test certificate 3.1, autoclaved aerated concrete only without perforated sleeve)

European Technical Assessment ETA-12/0166: Post-installed rebar connection, 330 ml, 420 ml and 825 ml cartridges only

Application area

Awning

Steel supports

Brackets

French balconies

Drill holes with a rotary drill (without impact mechanism)

Clean the drill hole:

2x blow out/2x mechanical brush out/2x blow out

Cut anchor rod to length and mark the desired insertion depths

Insert perforated sleeve

Screw mixer onto cartridge

Discard the first section of mortar (until the mortar is uniformly coloured - approx. 10 cm)

Completely fill with composite mortar from end of perforated sleeve

Press in anchor rod up to the bottom of the sleeve while turning slightly

Load can be applied to the reinforcement bar after observing the curing time

Mount component; do not exceed maximum torque

Cut tubular film clip before use!

Screw mixer onto cartridge

Before use, dispense a bead of approx. 20 cm

Create the drill hole

Clean the drill hole:

Blow out 4x with compressed air/brush out 4x mechanically/blow out 4x with compressed air

Cut anchor rod to length and mark the desired insertion depths

Screw mixer onto cartridge

Discard the first section of mortar (until the mortar is uniformly coloured - approx. 10 cm)

Fill composite mortar from bottom of drill hole

Press in anchoring element up to drill hole base while turning slightly

Visual check of mortar volume, embedment depth mark

Load can be applied to the reinforcement bar after observing the curing time

Mount the component. Do not exceed the maximum torque

Cut tubular film clip before use!

Screw mixer onto cartridge

Before use, dispense a bead of approx. 20 cm

Drill the hole

Clean the drill hole:

Blow out 4x with oil-free compressed air (min. 6 bar)

Brush out 4x mechanically

Blow out 4x with oil-free compressed air (min. 6 bar) (d. <20 mm and d. < 10xds)

Blow out 4x with hand pump, brush out 4x mechanically, blow out 4x with hand pump

Place the embedment depth mark on the rod and check the drilling hole depth

Screw mixer onto cartridge

Discard the first section of mortar (until the mortar is uniformly coloured - approx. 10 cm)

Mount injection equipment, fill composite mortar from bottom of drill hole

Insert the reinforcement bar until it reaches the mark, turning slightly

Visual check of the mortar volume, observe maximum processing time

Load can be applied to the reinforcement bar after observing the curing time

Minimum curing times in concrete
Temperature of base material	Processing time	Minimum curing time in dry concrete	Minimum curing time in wet concrete
≥ -10 °C¹⁾	90 min	24 h	48 h
≥ -5 °C²⁾	90 min	14 h	28 h
≥ 0 °C²⁾	45 min	7 h	14 h
≥ +5 °C²⁾	25 min	2 h	4 h
≥ +10 °C²⁾	15 min	80 min	160 min
≥ +20 °C²⁾	6 min	45 min	90 min
≥ +30 °C²⁾	4 min	25 min	50 min
≥ +35 °C²⁾	2 min	20 min	40 min
≥ +40 °C³⁾	1.5 min	15 min	30 min
¹⁾ Cartridge temperature: ≥ +15 °C ²⁾ Cartridge temperature: +5 °C to +25 °C ³⁾ Cartridge temperature: < 20 °C

Minimum curing times in masonry
Temperature of base material	Processing time	Minimum curing time in dry masonry	Minimum curing time in wet masonry
-10 °C to -6 °C¹⁾	90 min	24 h	48 h
-5 °C to -1 °C²⁾	90 min	14 h	28 h
0 °C to +4 °C²⁾	45 min	7 h	14 h
+5 °C to +9 °C²⁾	25 min	2 h	4 h
+10 °C to +19 °C²⁾	15 min	80 min	160 min
+20 °C to +24 °C²⁾	6 min	45 min	90 min
+25 °C to +29 °C²⁾	4 min	25 min	50 min
+30 °C to +40 °C³⁾	2.5 min	15 min	30 min
¹⁾ Cartridge temperature: ≥ +15 °C ²⁾ Cartridge temperature: +5 °C to +25 °C ³⁾ Cartridge temperature: < +20 °C

European Technical Assessment ETA-12/0164: Individual fixing point + cracked and uncracked concrete (W-VD-A anchor rod, standard threaded rod with acceptance test certificate 3.1), seismic performance category C1

European Technical Assessment ETA-13/1040: Individual fixing point + masonry consisting of solid and perforated block, autoclaved aerated concrete (WIT-SH perforated sleeve, WIT-AS anchor rod, WIT-IG internally threaded sleeve, autoclaved aerated concrete only with WIT-SH 18x95 perforated sleeve)

European Technical Assessment ETA-16/0757 and ETA-20/0854: Individual fixing point + masonry consisting of solid and perforated block, autoclaved aerated concrete (SH perforated sleeve, W-VI-A anchor rod, W-VI-IG internal thread anchor, threaded rod with acceptance test certificate 3.1, autoclaved aerated concrete only without perforated sleeve)

European Technical Assessment ETA-12/0166: Post-installed rebar connection, 330 ml, 420 ml and 825 ml cartridges only

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet 1

Safety data sheet 2

Certificates/ Documents

Application area

Anchoring in cracked and uncracked concrete, masonry consisting of solid and perforated brick, aerated concrete and for post-installed reinforcement rods.

Suitable for attaching metal structures, metal profiles, wooden structures, brackets, grids, pipes, cable conduits etc.

Instructions

A 330 ml and 420 ml cartridge can continue to be used until the best before date, by changing the mixer nozzle or resealing it with the end cap.

Type description	WIT-VM 250
Contents	420 ml
Included in delivery	Mortar cartridge 420 ml (coaxial) + 1 x mixer nozzle
Suitable application gun	Battery-powered application gun 420ml, Application gun MULTI, Application gun WIT 420ml, Pneumatic application gun 420ml, EasyMax 420 ml, HandyMax 420 ml
Min./max. processing temperature /conditions	-10 to 40 °C / temperature in the anchorage ground during processing and hardening
Min./max. ambient temperature / Conditions	-40 to 120 °C / after completely curing process
Temperature resistance, long-term temperatures max.	72 °C
Temperature resistance, short-term temperatures max.	120 °C
Shelf life from production/conditions	18 Month / cool and dry storage area, 5°C to 25°C
Approval	ETA-12/0164, ETA-13/1040, ETA-12/0166, ETA-16/0757, ETA-20/0854
Chemical basis	Vinylester, styrene free
Colour	Grey

¹⁾ Maximum long-term temperature ²⁾ Maximum short-term temperature ³⁾ The partial safety factors of the resistances regulated in the approval and ETAG 029 and a partial safety factor of the actions of γF = 1.4 have been taken into account. ⁴⁾ If the characteristic spacing and edge distances are reduced, the admissible loads must also be reduced. The smallest possible spacing or edge distance is the minimum spacing s_min or minimum edge distance c_min ⁵⁾ For combinations of tensile and shear loads, bending moments or reduced edge distances and spacings, see the European Technical Assessment. If the masonry joints are not visible, the load capacity should be reduced by a factor of α_j = 0.75. If the masonry joints are visible (e.g. on an unplastered wall) the following should be observed: 1. The load capacity may only be assessed when the masonry joint is filled with mortar. 2. If the masonry joints are not filled with mortar, the load capacity may only be assessed if the minimum edge distance c_min to the perpend joints has been adhered to. If this minimum edge distance c_min is not adhered to, the load capacity should be reduced by a factor of α_j = 0.75. Documentation for brick removal must also be supplied in accordance with ETAG 029 Annex C. ⁶⁾ The brick and hole geometry must be taken from the European Technical Assessment. ⁷⁾ N_adm or V_adm applies for the edge distance c_cr, clip value (N_adm) or (V_adm) applies for the minimum edge distance (c_min).

Anchor size	Brick compressive strength [N/mm²]	Brick density [kg/dm³]	Brick format⁶⁾[mm]	Effective anchorage depth h_ef [mm]	Minimum member thickness h_min [mm]	Maximum installation torque T_inst,max [Nm]	Admissible tensile load³⁾⁴⁾⁵⁾ (individual anchor without influence of the edge distance) N_adm [kN]	Admissible shear load³⁾⁴⁾⁵⁾ (individual anchor without influence of the edge distance) V_adm [kN]	Char. spacing parallel to bed joint⁴⁾ s_cr \|\| [mm]	Char. spacing perpendicular to bed joint⁴⁾ scr ⊥ [mm]	Minimum spacing ⁴) s_min [mm]	Char. edge distance c_cr [mm]	Minimum edge distance⁴⁾ c_min [mm]
Solid brick Mz-DF EN 771-1
M8 Perforated sleeve 12x80	10	1,64	240 x 115 x 55	80	115	2	1.0 (0.43)⁷⁾	1.0 (0.34)⁷⁾	240	240	120	120	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.29 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.57 (0.71)⁷⁾	1.57 (0.57)⁷⁾
M8 Perforated sleeve 16x85	10	1,64	240 x 115 x 55	85	115	2	1.0 (0.43)⁷⁾	1.0 (0.34)⁷⁾	255	255	120	127,5	(60)7)
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M8 Perforated sleeve 16x130	10	1,64	240 x 115 x 55	130	195	2	1.0 (0.43)⁷⁾	1.0 (0.34)⁷⁾	390	390	120	195	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M10/IT M6 Perforated sleeve 16x85	10	1,64	240 x 115 x 55	85	115	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	255	255	120	127,5	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M10 Perforated sleeve 16x130	10	1,64	240 x 115 x 55	130	195	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	390	390	120	195	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	27	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M12/IT M8 Perforated sleeve 20x85	10	1,64	240 x 115 x 55	85	115	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	255	255	120	127,5	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	27	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M12 Perforated sleeve 20x130	10	1,64	240 x 115 x 55	130	195	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	390	390	120	195	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	27	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M12 Perforated sleeve 20x200	10	1,64	240 x 115 x 55	200	240	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	600	600	120	300	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	27	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M16/IT M10 Perforated sleeve 20x85	10	1,64	240 x 115 x 55	85	115	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	255	255	120	127,5	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M16 Perforated sleeve 20x130	10	1,64	240 x 115 x 55	130	195	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	390	390	120	195	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
M16 Perforated sleeve 20x200	10	1,64	240 x 115 x 55	200	240	2	1.0 (0.43)⁷⁾	1.0 (0.43)⁷⁾	600	600	120	300	(60)⁷⁾
	20	1,64	240 x 115 x 55			2	1.43 (0.71)⁷⁾	1.43 (0.43)⁷⁾
	28	1,64	240 x 115 x 55			2	1.71 (0.86)⁷⁾	1.57 (0.57)⁷⁾
Solid sand-lime block KS-NF EN 771-2
M8 Perforated sleeve 12x80	10	2,0	240 x 115 x 71	80	115	2	1.0 (0.43)⁷⁾	0.71 (0.43)⁷⁾	240	240	120	120	(60)⁷⁾
	20						1.43 (0.71)⁷⁾	1.14 (0.71)⁷⁾
	27						1.71 (0.86)⁷⁾	1.29 (0.71)⁷⁾
M8 Perforated sleeve 16x85	10			85	115		0.86 (0.43)⁷⁾	0.71 (0.43)⁷⁾	255	255	120	127,5	(60)⁷⁾
	20						1.29 (0.57)⁷⁾	1.14 (0.71)⁷⁾
	27						1.43 (0.71)⁷⁾	1.29 (0.71)⁷⁾
M8 Perforated sleeve 16x130	10			130	195		0.86 (0.43)⁷⁾	0.71 (0.43)⁷⁾	390	390	120	195	(60)⁷⁾
	20						1.29 (0.57)⁷⁾	1.14 (0.71)⁷⁾
	27						1.43 (0.71)⁷⁾	1.29 (0.71)⁷⁾
¹⁾ Maximum long-term temperature ²⁾ Maximum short-term temperature ³⁾ The partial safety factors of the resistances regulated in the approval and ETAG 029 and a partial safety factor of the actions of γF = 1.4 have been taken into account. ⁴⁾ If the characteristic spacing and edge distances are reduced, the admissible loads must also be reduced. The smallest possible spacing or edge distance is the minimum spacing s_min or minimum edge distance c_min. ⁵⁾ For combinations of tensile and shear loads, bending moments or reduced edge distances and spacings, see the European Technical Assessment. If the masonry joints are not visible, the load capacity should be reduced by a factor of α_j = 0.75. If the masonry joints are visible (e.g. on an unplastered wall) the following should be observed: 1. The load capacity may only be assessed when the masonry joint is filled with mortar. 2. If the masonry joints are not filled with mortar, the load capacity may only be assessed if the minimum edge distance c_min to the perpend joints has been adhered to. If this minimum edge distance c_min is not adhered to, the load capacity should be reduced by a factor of α_j = 0.75. Documentation for brick removal must also be supplied in accordance with ETAG 029 Annex C. ⁶⁾ The brick and hole geometry must be taken from the European Technical Assessment. ⁷⁾ N_adm or V_adm applies for the edge distance c_cr, clip value (N_adm) or (V_adm) applies for the minimum edge distance (c_min).

Required accessory:

Product

Description

Quantity

Price
/PU

ANC-(W-VD-A/A4)-A4-20-M8X110

Art.-no. 5915208110

For W-VPZ and W-VD bonded anchor capsule systems and WIT injection systems in concrete

x 10 pcs

ANC-(W-VD-A/A4)-A4-60-M8X150

Art.-no. 5915208150

For W-VPZ and W-VD bonded anchor capsule systems and WIT injection systems in concrete

x 10 pcs

ANC-(W-VD-A/A4)-A4-35-M12X160

Art.-no. 5915212160

For W-VPZ and W-VD bonded anchor capsule systems and WIT injection systems in concrete

x 10 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Additive article:

Product

Description

Quantity

Price
/PU